UFRC-GR1 Ghost Rabbit 1/5  4WD Rear Straight Axle Electric RC Off-road Vehicle Model

Features:

Parameters: Proportion: 1/5
Maximum body size (L×W×H): 790×525×380mm (when wheels with a diameter of 230mm and a width of 100mm are assembled)
Wheelbase: 565mm; Front track: 420mm
Rear Wheelbase: 420mm
Drive form: Full-time four-wheel drive/3 differentials (standard rear axle differential lock and central differential lock)
Front suspension type: independent
Rear suspension type: straight axle
Caster angle (Non-adjustable): 20 degrees
kingpin inclination angle (adjustable): 3 degrees
Toe angle (adjustable): 3 degrees (outer horoscope)
Rear toe angle (non-adjustable): 0 degrees
Rear inclination angle ( Non-adjustable): 0 degrees
Approach angle: approximately 90 degrees
Departure angle: approximately 90 degrees
Passing angle: approximately 45 degrees
Minimum turning radius: approximately 1.5 meters
Maximum steering angle: approximately 30 degrees
Maximum longitudinal slope: approximately 50 degrees
The maximum angle of roll: about 40 degrees (the angle of the overall body roll when the front and rear axles are not cross-twisted)
The maximum torsion angle of the X-type front and rear axles of the body: about 80 degrees (need to remove the front and rear anti-roll bars and loosen Angle limit screw of front shock-absorbing cradle)
Hole distance of trailing arm (knife arm): 257mm
Ground clearance of bridge egg (wheel diameter 230mm): 75mm
Chassis ground clearance (wheel diameter 230mm): 115mm
Factory standard configuration Gear ratio: 14.9
Gear ratio range: 9-14.9 (The gear ratio can be changed by replacing the mid-wave box gear set)
Gear modulus: M1.5
Number of differential locks: 2, self-provided steering gear
Differential speed Lock position: center differential/rear axle differential
Rear shock absorption compression stroke: 80mm
Front shock absorption compression stroke: 53mm
Wheel size: diameter 230mm, width 100mm
Wheel adapter specification: 24mm (hexagonal)
Front shock-absorbing hole distance (two-stage spring shock absorption): 170mm
Rear shock-absorbing hole distance (two-stage spring shock absorption): 212mm
Maximum speed: A.8S power: 80KM/H (based on motor 750KV) / B .12S power: 110KM/H (based on motor 680KV)
Total weight: A.8S power: 22KG / B.12S power: 24.5KG
Maximum frame load: about 10KG
Empty frame weight (excluding wheels and Electronic equipment): 15.6KG

Electronic equipment configuration:
ESC: recommended 8S-12S
Motor: recommended market standard 1/5 automotive motor, such as 5692/56112/58113 (configuration motor reference data: motor housing diameter less than 65mm , The length of the shell is less than 118mm)
Battery: A.8S: 2 groups of 4S / B.12S: 2 groups of 6S (6000-12000mAh) in series
Battery compartment size: 193*125*100mm
Steering servo: quantity 2, specifications 15T, 50-85KG, general 1/5 steering gear (installation hole 17.5*75mm), built 70KG steering gear is recommended
Differential lock steering gear: quantity 2, 25T, 15-35KG, universal steering steering gear of 1/8 model (installation hole 10.0*49.5mm), 25KG steering gear is recommended
Remote control : Recommended 5 channels or above
Charger: Recommended 4S or above with lithium battery balancing function
Battery safe storage container: explosion-proof box/explosion-proof bag
Commonly used plug: A. Banana plug/BT plug
Commonly used tools: Allen wrench, Nut sleeves, circlip pliers, heat guns

General components:
Wheels: 1/5 car models on the general market are 24mm wheels with hexagonal couplings with a wheel diameter range of 190-230mm and a width of 70-100mm. When the diameter is greater than 190mm and the width is greater than 80mm, the steering angle needs to be limited, and the steering angle output is set within 75%;
A. For the car to handle and perform at its best, wheels of 100mm in width and 230mm in diameter are suggested. There is an inner liner that can significantly lower the chance of tyre explosion and cake rejection;
B. The tyre skin that is attached to the inner lining should be used when using 12S power; otherwise, unfavourable outcomes, like tyre explosions, may occur. The tyre skin and wheel hub should be bonded together using a strong glue (genuine, Henkel-approved Loctite 480 vinyl is advised). After testing, when the pressure ring is fixed, it is simple to induce a tyre explosion;

2. Differential star gear assembly (gear plus gear fixed frame):
BAJA differential 3 Nylon ball head buckle: General 5T models (ball diameter 11mm)

Core features:
With a wheelbase of 1/5 car and a strength of 1/4 car, the vehicle can support a maximum of 12S power. The car's length is economical and accounts for 1/8 of its cost. Since the entire vehicle is made up of metal, upgrades and repairs won't cost a lot of money down the road. To accommodate both low-speed climbing and high-speed driving, it incorporates two differential locks.
Frame version instructions:

Wheels, motors, ESCs, differential lock steering gears, steering gears, remote controls, batteries, chargers, standard tools, etc. must all be purchased individually. All you have to do is install and troubleshoot the electronic equipment as the frame is fully put together.

Specifications:

.Material: Metal + Plastic
.Product Dimensions: 79 x 52.5 x 38cm
.Product Weight: 15600g
.Package Dimensions: 90 x 62 x 45cm
.Package Weight: 19000g
.Packing: Carton Box