7 Steps To Clean Your RC Cars

RC cars are just as much fun for kids and adults to play with. When you take these rigid motorcycles for a spin, both off-road and on, you can experience an adrenaline rush unlike anything other. The majority of RC car owners, however, are hesitant to take their vehicles out for a leisurely drive due to the challenge of cleaning them afterward. You can't just use water and detergent to clean an electronic device. After a successful celebration, how do you clean your RC car?

After a challenging time on the track, it's critical to give your RC car a complete cleaning to keep it in top shape. For some people, cleaning an RC car might be a nightmare. However, did you know that you can easily clean your RC cars with the correct equipment and a little perseverance?

We'll examine the best practices for maintaining the cleanliness of your remote-controlled cars in this post.

7 steps to clean your RC Car

The best time to clean RC cars is immediately after driving them when the dirt is most straightforward to remove. This section will examine the procedures for properly cleaning an RC car:

Step 1: Remove the batteries 

Remove all electrical power sources from your car before you start cleaning it. You don't want to run the danger of damaging any of the car's electrical systems. To clean the chassis, bearings, and electrical wirings of dirt and loose debris, use compressed air and a brush.

These loose particles occasionally become trapped between the car's gears, causing severe wear and tear. Dirt can also lower the engine heat sink's and motor's cooling effectiveness. Therefore, it is crucial to remove this loose dirt and debris.

Step 2: Remove the tires and clean 

If you've removed any locations or debris, you've got time to clean your RC car's tires. Using a toothbrush and a low-pressure hose, carefully remove the tires and give them a good cleaning. Once the dirt and debris have been removed, the tire should be cleaned with water.

Your RC car may vibrate and become less stable if its tires have too much mud and dirt on them. The primary reason for this is the wheels uneven weight distribution.

Cover the tires' breathing holes to prevent them from absorbing water. Now that the wheels are gone clean the steering and suspension of any dirt or debris.

Step 3: Spray the RC Car with a general cleaner

Warm water and detergent can be used to clean your remote-controlled car and its electronic components if they are waterproof. To get rid of any mud or caked filth, give the wheels, chassis, suspension, and bearings a thorough cleaning with a toothbrush. After cleaning your RC car, be careful to let it air dry in the sun. We shouldn't be allowed to stay on the electronic parts or chassis.

If your remote-controlled isn't watertight, you can clean it with denatured alcohol. Alcohol wipes can also be used to clean the chassis of dirt and debris. You can also clean the nuke and its corners with a toothbrush dipped in denatured alcohol. If don't have access to denatured alcohol, you can use any general cleaner on the market.

Step 4: Let the car dry

To dry the water, ideally, leave the automobile in the sun for a while. To finish the task quickly, blow off the water with low-pressure air. To get rid of any last traces of moisture, you can also clean the automobile with a gentle towel.

Step 5: Look for any signs of rust

If you are driving an old remote-controlled vehicle, the likelihood of discovering rust is considerable. Scrutinize the car for any indications of rusting after it has dried. If you detect any, use chemicals or anti-rust sprays to get rid of it. After cleaning, you should ideally spray rust inhibitors like WD-40 on all exposed bearings and metal caps.

Operating an outdated remote-controlled car carries a significant risk of rust. Once the vehicle has dried, thoroughly inspect it for signs of corrosion. Use chemicals or anti-rust sprays to remove any that you find. After cleaning, all exposed bearings and metal caps should ideally be sprayed with rust inhibitors, such as WD-40.

Step 6: Clean the cars body

The majority of remote-controlled automobiles have plastic bodies. Use a standard cleaning solution to give the car's body a thorough cleaning. Brush the body to remove dirt or debris. To eliminate even the slightest hint of dampness, wipe the body with a dry cloth and leave it in the sun.

You can even apply polish to the body to achieve a glossy appearance. Several high-quality polishes are readily accessible on the market.

Step 7: Lubricate the joints and other moving parts

After giving the car a good cleaning, you may have also removed the lubricants from the joints. As advised by vehicle's user handbook, lubricate the suspension and drive train parts with WD-40 oil. After the car has been properly lubricated, reassemble it.

Pro tips for cleaning RC Cars

After talking about the best ways to clean your remote-controlled sets, have a look at some expert cleaning advice:

1. After you take your RC car for a spin, make it a routine to clean it. Particularly if you have off-roaded it. The likelihood of dirt and loose debris entering car's gearbox and increasing the likelihood of rusting is high.
2. To reduce the chance of a short circuit, always take off the battery or power source before washing your vehicle. Ensure the chemicals you use to clean your car do not end up in the electric components of your car.
3. Make sure the cleaning agents don't get into the car's electrical systems.
4. When cleaning off-road vehicles, it is recommended to remove the rear wings and tires. You can clean the suspension more efficiently as a result.
5. Before putting the automobile away, check its bearings and grease them if necessary. Use approved lubricants for improved durability and performance.

Conclusion

A well-maintained and clean RC car always gives its best performance. Regular cleaning also ensures better durability and life for your RC car. We hope that this article helps you clean your RC cars more efficiently. You can also check out other RC car care products from our website.